
Help & Support
Troubleshooting
Support Library
FAQs
Downloads
Suggested Reading
Setup Information
Software Setup
Server Settings
Access Numbers
New User Tutorial
Your Web Space
Need More Info?
Tech Support
1-800-715-7873
DSL Tech Support
1-888-899-1500
|
 |
 |
Troubleshooting Lock Ups and Crashes in Netscape on a Macintosh
Crashes and Lock-ups on any computer is an unfortunate fact of life. Macintosh is no different. The most common
types of error you will get on a Macintosh are type 11 and type 1. They're basically caused by improper RAM handling,
extension conflicts, preferences errors, or other deeper, system wide errors. Here's the official word from Apple on
Type 11 errors.
A Type 11 error is listed as a hardware exception error. However, As with all Macintosh Type xx errors, they
usually do not identify a particular software or hardware component error. Type xx errors are more general in nature.
You may see more Type 11 errors on a Power Macintosh computer because of problems with the software-based 68k
emulator. The emulator allows the RISC processor to run older Macintosh software. If the emulator gets corrupted
while loading into RAM, then some of the failures caused by this are reported as Type 11 or Hardware Exception
errors. The emulator can get corrupted by either incompatible software or faulty hardware.
This document is meant to help you troubleshoot type 11, type 1, and other errors that may be causing netscape
to crash. Sometimes crashes can be fixed simply from within the program. Other solutions can be more obscure.
We're going to cover information from Netscape and getting rid of the Type 11 errors caused by Netscape, and
we're also going to give you the information that Apple provides for clearing up chronic system crashes.
Contents
Troubleshooting Lock-Ups and Crashes
- Quick Fixes
- More Advanced Solutions
Netscape Article 970808-15: General Macintosh Trouble Shooting
- 1. Conflict Test
- 2. Give Netscape more memory
- 3. Turn off all Software based memory programs (RamDoubler, OptiMem)
- 4. Increase the Apple Disk Cache in Memory Control Panel
- 5. Turn off Modern Memory Manager with system 7.5.3 or lower
- 6. Upgrade MacTCP 2.0.6 or Open Transport 1.1.2
- 7. Trash the Netscape Preferences
- 8. Rebuild the desktop
- 9. Run MacTools, Norton Disk Doctor, or Disk First Aid
- 10. "Clean" Install the System Software
- 11. Helpful info on incompatible programs or program versions
Netscape Article 980911-9: Macintosh version of Communicator freezes, or quits with an error "Type 11".
Further Troubleshooting
Other Suggestions
Troubleshooting Lock-Ups and Crashes
Quick Fixes
- Clear Netscape's Disk Cache (if Netscape still runs).
From within Netscape, click on the "Options" menu and choose "Network Preferences". Click on the "Cache" tab. Click on "Clear Disk Cache Now".
- Increase Netscape's buffer size & decrease the maximum number of
connections. From within Netscape, go to the "Options" menu and
select "Network Preferences". Click on the "Connections" tab and
decrease the maximum number of connections. Increase the buffer
size as large as possible.
- Give Netscape more memory.
Find the Netscape Navigator icon on the hard drive and click on it
ONCE. Go under the "File" menu and choose "Get Info". If you have
enough memory on your Macintosh, increase the Preferred size by a
few thousand.
More Advanced Solutions
If problems persist follow these "Basics"
- Trash the Netscape Preferences.
Go into the System Folder->Preferences->Netscape folder and drag
the Global History and Netscape Preferences files to the trash. Go
into the "Cache f" folder and drag ALL these icons to the Trash. If
you use Netscape to send and receive E-Mail you'll need to reenter
all the information into Netscape so that you can continue to
send/receive E-Mail, but this may also remedy the crashes.
- Disable the Netscape Plug-ins.
Go into the Netscape directory on your hard drive. Open the
"Plug-ins" folder. Drag everything EXCEPT the "Default Plug-in"
out of this folder and to the Desktop. This will disable all your
plug-ins, one of which may be causing you a problem.
- Extensions & Control Panel Troubleshooting.
Go under the Apple menu to the Control Panels and open the
Extensions Manager. Since too many Extensions & Control Panels can
cause conflicts and crashes, you're going to want to disable as
many as you can... even if it's only temporary.
- Zap the PRAM.
Reboot the machine, then immediately hold down the "option",
"Apple", "P", and "R". Hold them until you hear the restart chime
three times, then let go and allow it to continue restarting
normally.
- Rebuild the Desktop.
Do this by restarting and holding down the "option" and "Apple"
keys through the restart process. Once the machine is back up, it
will ask you if you want to rebuild the Desktop. Click "Ok".
- Check out your hard drive.
If you have purchased either MacTools Pro or Norton Disk Doctor,
run a check on your hard drive. If you don't have either of these,
it would be a good idea to run the "Disk First Aid" program which
can usually be found on your System CD-ROM or your Utilities floppy
disk.
- Make sure you have the latest version of either MacTCP or TCP/IP
That will run on your system. The latest MacTCP is currently 2.0.6.
TCP/IP is currently at 2.0.1.
- Turn Virtual Memory off.
Type 11 errors are often seen when Virtual Memory is on. Go to
your Control Panel and make sure the Virtual Memory is off. If you
are using either RamDoubler or OptiMem, make sure they are
disabled.
Type 11 and Type 1 errors can be very common when using Netscape. Because of that, Netscape has outlined some
troubleshooting measures.
Here's Netscape's version of the fix -
Netscape Article 970808-15: General Macintosh Trouble Shooting
Note: Some of the troubleshooting measures here have also been outlined above.
From article http://help.netscape.com/kb/consumer/19970808-15.html
|
Issue: |
970808-15 |
Product: |
Navigator, Personal Edition |
|
Created: |
08/08/97 |
Version: |
1.x,2.x,3.x,4.x |
|
Last Updated: |
12/07/98 |
OS: |
Mac OS |
Topic:
The following are the basic troubleshooting steps used to resolve
most problems with the Macintosh and Navigator/Communicator. (Click the
links below for detail.)
- Conflict Test
- Give Netscape more memory
- Turn off all Software based memory programs (RamDoubler, OptiMem)
- Increase the Apple Disk Cache in Memory Control Panel
- Turn off Modern Memory Manager with system 7.5.3 or lower
- Upgrade MacTCP 2.0.6 or Open Transport 1.1.2
- Trash the Netscape Preferences
- Rebuild the desktop
- Run MacTools, Norton Disk Doctor, or Disk First Aid
- "Clean" Install the System Software
- Helpful info on incompatible programs or program versions
- Conflict Test
Errors on a Mac can often be traced to conflicts between Control
Panels and Extensions. Thus, if you disable all but the bare-minimum
necessary to run Netscape, you've eliminated many variables that
could affect the Mac.
- System 7.5 and 8.x comes with the Extensions Manager Control Panel.
Go to the Apple menu, select Control Panels, and open Extensions
Manager.
- In the top-right corner of the window is the Set-list.
Choose Save Set and name it "Before Netscape". (If you ever need to return to
your old configuration, open the "Before Netscape" set.)
- Turn off any extensions that you do not need for the Internet.
Go back to the Set-list popup menu and select Save Set. Name it "Minimal".
- Restart the computer to put your changes into effect.
Note: There are other Extensions Manager utilities out there.
Conflict Catcher and Now Startup are probably the most popular. If you
have one of those, make sure anything with "TCP", "PPP", and "Open"
(as in Open Transport) is turned on. If you have any questions about it,
check out your manual.
- Give Netscape more memory
Netscape on the PC has both a disk cache and a memory cache in the Network
Preferences, but Netscape on the Mac has only a Disk Cache setting.
To find the Memory Cache:
- Make sure Netscape is not running. To do this, go to the Applications Menu
in the top-right corner of the screen and make sure "Netscape" is not
listed. If Netscape is running, select the Netscape item from the menu,
go to the File menu, and select Quit. (command Q is the keyboard
equivalent.)
- Once Netscape is closed, select the Finder item from the Applications
menu.
- Find Netscape. Click it once. (Do not open the file; if you did, make
sure to quit Netscape again before proceeding).
- Go to the File menu and select Get Info.
There are two boxes here under Memory Requirements: Minimum size and a
Preferred size. Do not change the Minimum size. Change the Preferred
size box to anywhere between 16000 and 20000, depending on the amount of
RAM you have available. This is a rough value that should give Netscape
all of the elbow-room it needs. You can increase or decrease this value
based on how much RAM is installed on the computer, whether you'll be running
plugins or not, and whether some unused memory is needed for Helper Applications.
Note: If the Preferred size is greater than the amount of free RAM,
the max amount possible will be allocated. You'll get "Out of Memory"
errors when you attempt to run helper apps. This is a non-fatal error,
so there is no need to be too concerned if you see this.
- Turn off all software-based memory programs such as RamDoubler or OptiMem.
You can do this by disabling the extensions for these programs within
the Extension Manager.
- Optimize the Apple Disk Cache (in the Memory Control Panel)
There is a Disk Cache setting inside the Memory Control Panel. It should be
set to 32K per every 1 MB of physically installed RAM you have on your computer.
For example, if you have 8MB of RAM, you'll set it to 256K, if you have 16MB of RAM,
you'll set it to 512K, etc.
Note: If you can't find the Memory Control Panel, it may be disabled. Turn it on
using the Extensions Manager Control Panel and restart.
- Turn off the Modern Memory Manager (if present in the Memory Control
Panel)
This should help improve compatibility. Inside the Memory Control Panel there
may be a heading called Modern Memory Manager. If present, click the Off
button. (*NOTE-- If you are running system 7.5.5 or 7.6.x do NOT turn MMM off.)
- Upgrade MacTCP or Open Transport.
Contact Apple for the latest versions of these products.
- Delete the Netscape Preferences.
To do this within Netscape Navigator:
- Quit Netscape if it's running. Make sure it doesn't appear in the applications menu,
the menu in the top-rightmost corner of the screen. If it is listed, select it, go to the File
Menu and select Quit.
- Open the HD. Open the System Folder. Open the Preferences folder.
Open the Netscape f folder.
- Drag the bookmarks.html, Address.html, the Mail folder and the Java
folder to the desktop.
- Drag the Netscape f folder to the trash
- Go to the Special menu and select Empty Trash.
- Launch Netscape, which will rebuild the Netscape f preference folder.
- Drag the Mail and Java folders from the desktop back to the Netscape
f folder
- After your problem is resolved, you can import your address book and
bookmark files that you have saved back into the newly created Netscape f folder.
To do this within Netscape Communicator:
- Open the hard disk, System folder, and then the Preferences folder.
- Locate the Netscape Users folder; it contains User Profiles and an
item with (probably) your name on it.
- Double-click that icon.
- From the folder that opens, throw away Cache f and Global History
- Finally empty the trash.
- Rebuild the desktop
Restart the Mac, hold down the option and command keys until the Mac asks
"Do you want to rebuild the desktop?". Choose Yes.
This may take up to 10 minutes.
- Run MacTools, Norton Disk Doctor, or Disk First Aid
These first two are payware HD diagnostic programs. The third is a free disk
diagnostic that comes with all Macs on either the Disk Tools floppy or the
Apple System CD-ROM. Do not run these if you use any HD driver-level
compression program such as TimesTwo or Stacker. If you don't know, then you probably
don't have this type of program on your computer. Also, do not run these utilities if
you use a Security program such as Empower or FolderBolt on your Mac.
- "Clean" Install the System Software
A "Clean" install replaces all of the Apple components in the System Folder
with new copies. A typical install doesn't do this. Call Apple for
instructions.
- Some more helpful information on incompatible programs or program versions:
Incompatible with FreePPP 1.0.5 and earlier:
- RamDoubler 1.6.0 and earlier can get in the way of FreePPP and cripple
the connection.
- RamDoubler 1.6.1 is OK. Upgrade at http://www.connectix.com.
Incompatible with Netscape:
---End Article 970808-15---
Netscape Article 980911-9: Macintosh version of Communicator freezes, or quits with an error "Type 11".
From article http://help.netscape.com/kb/consumer/19980911-9.html
|
Issue: |
980911-9 |
Product: |
Communicator |
|
Created: |
09/11/98 |
Version: |
4.x |
|
Last Updated: |
02/10/99 |
OS: |
Mac OS |
Problem:
Macintosh version of Communicator freezes or quits with an error "Type 11".
Solution:
This can be caused by file corruption, extension conflicts or
insufficient system resources. First of all, check that memory is
configured correctly.
- Go to Control Panel and then Memory.
- Make sure that the Disk Cache is set to 32k for every
megabyte of RAM installed, and that virtual memory is set to 1.5 to
2 times the RAM installed.
- Go to the Netscape Communicator Folder and click once on Netscape
Communicator (do not open the folder).
- From the File menu, select Get Info, and in the window
that opens, increase Preferred Size by 2-3000k.
You may also need to let Communicator rebuild its Cache folder:
- Go to System Folder, Preferences, and Netscape Users.
- Open the folder with your name on it.
- Drag the Cache folder to the Trash to delete it.
- When you relaunch Communicator, it should rebuild
the folder automatically.
If these suggestions do not work, download the update for Communicator 4.08 at:
http://home.netscape.com/download/index.html.
---End Article 980911-9---
Further Troubleshooting
If none of the above fixes the problems, there are still some steps we can take.
- Try installing a different version of Netscape. If you are running an older version of Netscape, you may want to try upgrading to Netscape Communicator.
You can download Netscape Communicator for free from the sites listed below. Please make sure to install the most appropriate version for your system:
- 68k (7.6.1 or higher, minimum 16 megs of ram)
- PPC (7.6.1 or higher, minimum 16 megs of ram)
Conversely, if you are on an older computer, and are trying to run Netscape Communicator, you may want to downgrade to netscape 3.04.
- 68k
- PPC
Note: These links can change without notice. If you think one of these links has changed, please contact support@core.com
- Remove all of Netscape's plug-ins
Netscape Navigator
Go to Hard Drive -> System Folder -> Preferences->Netscape f -> Plug-Ins and remove all of them EXCEPT the Default Plug-In.
Netscape Communicator
Go to Hard Drive -> Netscape Communicator folder -> Plug-Ins and remove all the plug-ins Except the Default Plug-In
This will shrink Netscape's operating size.
- Disable the Java and JavaScript
Netscape Navigator
With the program open, go to Options->Network Preferences, and click onto the Languages tab. Uncheck both Javascript and Java
Netscape Communicator
In Netscape, go to Edit -> Preferences -> Advanced. Uncheck Java and Javascript.
Other Suggestions
If you are only have sporadic errors, you may want to consider upgrading to the newest operating system your computer
can support. While Type 11 and Type 1 errors can happen on any Macintosh at any time, Apple has made great improvement
for memory handling in its newer operating systems, such as 8.1 and 8.5. This has cause a huge decrease in the frequency
in these errors. For that reason, we strongly recommend upgrading to the newest operating system if your computer meets
the minimum system requirements for the upgraded operating system. Consult your Apple Technician for help deciding if
you should upgrade.
In rare cases, we have also see where Netscape is just not compatible on some Macintosh systems. You may want to
try running Microsoft's Internet Explorer and see if that runs without errors. You can download it from
Microsoft's site.
If these problems are constant and persist even after going through this troubleshooting guide, there could be a
problem with the computer. In this case, you will need to have a computer technician look at your computer.
| Document History |
| Last Updated: | 05/05/04 |
| Last Reviewed: | 10/12/03 |
|